Constructed completely out of cast iron, the new Felder 700 Series saw unit represents a new era of running stability and efficiency.
104 mm cutting height with a 315 mm saw blade
operates with groover up to 19.5 mm
Electrical height adjustment with LED display
Zero point tilt
Large dimensioned saw arbor with double bearing seats
Maximum energy transfer with the large Poly-V belt ­bearing area
Optimal extraction with the completely enclosed, below table extraction system
Precise height adjustment via precision linear guides
High precision double-sided support system
Tilt segment “Easy-Glide”:
- High durability
- Play-free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required

The electronically balanced saw arbor with dual bearing seat system is powered via a Poly-V belt. This combination results in an almost perfect transmission of power to the saw blade.

The Felder 700 Series saw unit is fully compatible with dado tooling. Thanks to removable flanges and table insert, the Felder designed, fully adjustable dado cutters can be used.

No reading errors due to scales and vernier. No time-wasting with arduous approximations of angle values. The advantage of the Felder degree index is that the stop is set and fixed without losing time or making reading errors. Highly precise index positions allow for the accurate production of polygons, e.g. 5.625º (32 sided), 11.25º (16 sided), 22.5º (8 sided). In addition, index positions at 15º, 20º, 25º, 30º, 35º, 40º and 45º can be used when working in slide to cut or push to cut mode. Every index position is equipped with a length compensator. The highly precise Felder degree index system is adjusted in the factory. Every index position also has individual fine adjustment. The index system, which integrates well into the machine design, increases your productivity to achieve unrivalled cost effectiveness.

The crosscut fence 1100 mm for crosscuts between +45° and –45°. The fence can be attached to the sliding table without the use of tools. The end stop provides you with the exact 90° position.
The bevelled mitre scale with accurate readout is visible from the operating area and thus enables exact setting of the required crosscut value.
The large crosscut fence stops are constructed in such a way that a small tongue on the stop fits perfectly into a groove on the fence. This means the crosscut fence stop remains firmly in place, especially useful when crosscutting pre-mitred workpieces.

Settings with an accuracy to a tenth of a millimetre can be obtained using the electronic digital display incorporated in the parallel cutting fence. Option

The Felder device for tilting the feeder away means the power feeder always remains on the machine and can be used at any time with no difficulties.

The outrigger table enables the user to process large, heavy work pieces. Eight rollers guide the telescopic support arm, ensuring precision and stability.

The “precision mitre index system” on the outrigger table of the professional model allows you to freely select preset positioning stops at increments of 5°, but also at 22.5°, by means of the index locating pin from +45° to –45°.

The scoring unit for cuttings in plastic laminated panels without tear outs. Backlash free height and lateral adjustment of the scoring saw blade, drive power of the industrial scoring unit 1.0 HP.

The Felder precision sliding table has been designed to accept maximum loads while retaining its smooth operation and accuracy. The “Monoprofile“ of the sliding table and base guarantees maximum ­torsional strength at every temperature. Through the “X“ formation of the roller bearings the load is optimally distributed to all sides. The “X-Roll“ guiding system and other numerous outstanding details are patented. Such precision and technology earns the right to the status of “World Class“.

With a completely new design, the Felder “700” spindle unit sets new standards!
Spindle operating height of up to 115 mm
Table opening: 230 mm
Quick-change system for moulder spindle
4 Operating speeds (3,500, 6,500, 8,000, 10,000 rpm)
Change of speed from front of machine
Fully compatible with high speed router spindle at 15,000 rpm
Tilts backwards 0° to 45°
Electrical height adjustment with LED display
High precision double-sided support system
Dovetail guidance system for height adjustment
Maximum energy transfer with the large Poly-V belt ­bearing area
Excellent vibration absorption from heavy cast iron unit
Tilt segment “Easy-Glide”:
- High durability
- Play-free tilt
- Unaffected by dust
- Completely maintenance free
- No lubrication required

The high speed router spindle is designed for router shaft diameters of Ø 6–16 mm at a running speed of 15,000 rpm.

The tilting segment on the Felder 700 series has one small but important detail: it is completely free of lubrication!

All Felder spindle moulders tilt 90°–45° as standard.

As soon as you begin working on your machine, you’ll see that your Felder’s range of applications is much wider than you might have expected and you save a lot on tools too. Using the hand wheel causes the whole moulder spindle unit to tilt to the requested angle easily and smoothly.

Accurate slots and tenons are much easier with the ­Felder “X-Roll” sliding table. This precision guiding system will accept maximum loads without compromising the smooth and accurate stroke of the sliding table. The “X”-configuration of the roller bearings optimally distributes workpiece weight to all sides. With conventional sliding tables, ball bearings are used in the guiding system. A ball bearing system creates a singular point of contact between the bearings and the flat guiding tracks. The singular point of contact will eventually wear grooves into the tracks and as a result, sideways play will develop in the sliding table. It is physically impossible for the “X-Roll” system (with roller bearing lineal contact) to wear grooves into the guiding tracks, hence the system will always remain play-free and is backed with a 6-year factory guarantee.

The “240“ spindle fence is standard equipment on the spindle moulders. The spindle fence can accommodate tooling to a maximum of 230 mm and has a fine adjustment on the spindle fence outfeed side. The integrated dust extraction connector allows for chip removal. The spindle table opening is 230 mm. That is your advantage when panel-raising ­­– the spindle tooling can be lowered under the table.

The MULTI-adjustment system allows quick adjustment to the workpiece diameter, also ensuring parallel running of the moulder fence.
- automatic repeat setting after removal of your fence
- parallel adjustments of the moulder fence
- Fast and fine adjustment
- measurement scale for depth of cut

More than 50 % of our clients now decide to take electric height adjustment for the moulder spindle.

The safety bar guides, great for “end-grain” work (optional).

- Safe operation
- Suitable for any workpiece size
- Problem-free power feeder application
- Impeccably machined surface
- Optimal chip removal

On request, we can equip your “700 Series“ with start buttons located directly on the sliding table to turn on the main and scoring blades. How about that for convenience!

The rip capacity comes at 800 mm or optional 1250 mm. The rip fence almost hovers over the table. The single handed quick clamping and fine adjusment systems ensure quick and accurate setting of the rip fence. The easy to read rip scale is perfectly integrated into the saw table. The aluminium rip fence plate can be moved backwards to optimise the feed of workpieces. When working with narrow and thin cuts of wood or with the saw blade tilted, it can be inverted and used in the lying position.